APCNetShelter SX的24U机柜pdf,APCNetShelter SX的24U机柜易于安装，管理电缆，配电集成，并最大限度的气流优化的功能丰富的外壳。包括：脚轮，门钥匙（S），调平脚，顶板，侧板，用户手册The American Power Conversion(APC)Net Shelter SX 600-mm wide 24U enclosure is ahigh-quality enclosure for storage of industry-standard(ela-310), 19-in rack-mount hardware, whichincludes servers and voice, data, networking, internetworking, and APC power protection cquipmentAR310424U482mm(19in)600mm(23.62in)1070mm(42.13in)One U=4445 mm(1.75 in). See"Identify one U-space on the vertical mounting flange"on page 18Rear cable channel8 CastersSplit doors(with cable access under left-hand9 Bolt-down bracketdoor)3 Rear door cable containment bracket10 Reversible curved door4 Side panels with locks0 APC nameplateFrame posts12 Key6 Adjustable leveling feetVertical mounting flangeso Hardware bagRoofTorx T30/+2 Phillips wrench(1)Cage nut tool (1)PhillipsUtility knifeLevel (1)13-mm open-ended10-mm socketscrewdriver(1)wrench(1)wrench(1)①0的2Plastic cupM6x16M5x12Cage nuts 7-mm holewashers(60) Phillips slot screws(4)plugs ( 4)screws(60)1. Move the shipping pallet to a firm, level surface in an open area. Inspect the enclosure for visiblesigns of shipping damage. If you detect shipping damage, contact APC Customer Support at thenumber listed on the yellow label on the front of the enclosure or on the back cover of thismanual2. See the label on the packaging to determine where to cut the wrapping. Using sturdy shears orutility knife, carefully remove the plastic stretch wrap surrounding the enclosureSave the bag containing the warranty card and installation manual3. Remove the four cardboard corner protectors4. Remove the two pallet-mounting brackets that anchor the enclosure to the shipping pallet, using a13-mm wrench(not providedSave the pallet-mounting brackets if you plan to bolt the enclosure to the floorSee"Rack stabilization options"on page 95. With one person on each side of the enclosure, carefully roll it toward the rear of the pallet untilthe rear casters clear the back edge of the pallet. Continuc to slide the enclosure rearward until therear casters touch the floor6. While one person carefully tips the enclosure slightly away from the pallet have the other personpull the pallet away from the enclosure. Set it gently on its casters①wle pallet if you plan to reship the encl7. If you are not using a rack stabilization option use the 7-mm hole plugs(provided) to cover theholes that were used to attach the pallet-mounting bracket to the framea The shipping materials are recyclable. Save them for later use, or dispose of themappropriately.APC is not responsible for damage sustained during reshipment of this productAfter unpacking the enclosure, verify that all required components and hardware have been shipped withthe enclosure. See "Product Inventory"on page 2 for a list of componentsIf any items arc missing, contact APC Customer Support at a number on the back coverof this manual or at the apc Web siteThe enclosure can be moved on its casters with up to 1020 kg(2, 250 lbs)of equipmentinstalled. Push the enclosure from the front or the back, not the sides it may be unstable when pushedfrom the side. For greater stability, load 27 kg(60 lbs )or more of equipment into the enclosure beforemoving it on its castersIf lifting of the enclosure is necessary, this can be done by removing the hole plugs andattaching eye bolts(not included) to the top of the enclosure frame. Use appropriately rated M10 eyebolts with a shoulder for angular lifting. The maximum weight of installed equipment should be 142 kg(312 lbs )per eye bolt(567 kg [1, 250 lbs] total